SITE MAP JAPANESE FPX series illustration *Click a picture above for enlarging view.   Feature FPX series achieves high accuracy and productivity. This forging press adopts 2 points and long guided slide made of cast steel. Press frame : At the structure, its crown and bed are made of cast steel and steel plate, where higher load is applied. Divided frames are fixed with strong heavy-duty tie rods by heat-shrinkage. In this way, compressive stress is applied to the press frame. Surface of slide guide is machined precisely with supersized NC plano miller after shrinkage fit with heavy-duty tie rods. Slide : 2 points type of con-rod and a long guided slide made of cast steel are adopted against a large offset load. To minimize gap at slide guide, X-type of guide structure is adopted. The structure compensates heat deformation of the slide guide. Drive mechanism : Due to mechanism of suspended the flywheel at the main sleeve, load against the eccentric shaft and the main bush is reduced. Risk of heat generation is also prevented. Shut height adjustment : shut height adjustment is carried out by changing position of the eccentric wrist pin (Our Utility Model). The wrist pin is moved by hydraulic motor driven screw. The adjustment is able to be controlled at remote location. Amount of adjustment can be shown at digital counter located at the control panel. Clutch and brake : For improving maintainability, block type of lining is adopted for both clutch and brake. FPX Series Specifications FPX-1600 FPX-2000 FPX-2500 FPX-3000 FPX-3500 FPX-4000 FPX-5000 Standard Long Standard Long Standard Long Standard Long Standard Long Standard Standard Press force (MN) {tf} 16 20 25 30 35 40 50 {1600} {2000} {2500} {3000} {3500} {4000} {5000} Stroke distance (mm) 330 700 350 700 360 700 360 500 420 500 500 500 Press speed (spm) 80 20∼35 75 20∼35 70 20∼35 65 20∼35 55 20∼35 45 43 Shut height (mm) 800 1400 900 1500 1040 1500 1200 1270 1200 1270 1300 1400 Slide adjustment (mm) 7 8 8 8 8 8 8 8 8 8 10 10 Table dimensions R-L(mm) 1250 1700 1300 1800 1500 1800 1600 1600 1800 1800 2200 2300 F-R(mm) 1100 1400 1300 1500 1500 1500 1600 1600 1700 1700 1900 2100 Slide knock-out (kN×mm) 100×35 300×50 150×35 300×50 200×35 300×50 300×35 350×35 400×50 350×35 400×50 500×50 {tf×mm} {10×35} {30×50} {15×35} {30×50} {20×35} {30×50} {30×35} {35×35} {40×50} {35×35} {40×50} {50×50} Bottom knock-out (kN×mm) 200×50 600×150 300×50 800×150 300×50 800×150 400×50 800×100 500×50 800×100 100×50 120×50 {tf×mm} {20×50} {60×150} {30×50} {80×150} {30×50} {80×150} {40×50} {80×100} {50×50} {80×100} {10×50} {12×50} Main motor (kW) 90 160 110 220 150 220 190 260 220 315 355 400 Number of tripping (tpm) 25 20∼35 25 20∼35 25 20∼35 25 20∼35 25 20∼32 20 20 Max.30 Max.40 Max.30 Max.40 Max.30 Max.40 Max.30 Max.40 Max.28 Max.35 Max.25 Max.24 TFPX2000 TFPX4500L Personal Information Protection PolicyTerms of Use Copyright(C)2009 Sumitomo Heavy Industries Techno-Fort Co.,Ltd. All rights reserved.